New Products

Bante900P pH/Conductivity/DO Meter

Multiparameter meter, 15 function parameters can be selected, including 8 measurement modes.

pH Mode:
• Portable multiparameter water quality meter is equipped with a large backlit LCD display.
• 1 to 5 points push-button calibration with auto-buffer recognition.
• Selectable pH buffer standard (USA/NIST/DIN) or using the custom calibration solutions.
• Automatic electrode slope display helps user decide whether to replace sensor.

ORP Mode:
• Single point offset calibration allows adjusting the displayed value to a known standard.
• Relative and absolute millivolts measurement modes provide accurate ORP readings.

Portable Multiparameter Water Quality Meter

Ion Mode:
• 2 to 5 points calibration including the eight concentration calibration points can be selected.
• Automatically recognize ion selective electrodes, does not need to specify type of ion.
• Direct ion concentration readout simplifies the elaborate measurement process.
• Selectable multiple concentration units include the ppm, mg/L and mol/L.

Conductivity/TDS/Salinity/Resistivity Mode:
• 1 to 5 points push-button calibration with automatic calibration solution recognition.
• Selectable cell constant (0.1/1/10), normalization temperature (20/25°C), TDS conversion
  factor, seawater and practical salinity measurement modes.
• Linear or pure water compensation improves measurement accuracy of meter.

Dissolved Oxygen Mode:
• 1 or 2 points calibration using the air-saturated water and zero oxygen solution.
• Manual salinity and barometric pressure compensation improve the measurement accuracy.

Portable Multiparameter Water Quality Meter

Other Features:
• Automatic Temperature Compensation provides accurate reading over the entire range.
• Calibration Due Reminder prompts user to calibrate the meter regularly.
• Stability indicator automatically shows current measurement status.
• Auto-Hold function freezes stable measured value for easy viewing and recording.
• Manual temperature calibration corrects temperature deviation.
• Selectable temperature unit (°C or °F) meets different application requirements.
• Automatic electrode diagnosis shows zero point offset and slope of the electrode.
• Help message as a operational guide that helps you quickly begin using the meter.
• System menu allows setting the 15 parameters, including the number of calibration points,
  resolution, stability condition, measurement unit, etc.
• Reset feature automatically resumes all parameters back to factory default settings.
• Expanded memory stores and recalls up to 500 readings.
• Built-in real-time clock stamps stored data to meet GLP standard.
• Stored data can be transferred into computer by USB communication interface.
• Multi-mode power scheme (battery, power adapter, computer's USB port) ensures that use
  the meter smoothly.

Model


Bante900P

pH



Range


-2.000~20.000pH

Accuracy


±0.002pH

Resolution


0.1, 0.01, 0.001pH, Selectable

Calibration Points


1 to 5 points

Calibration Solutions


USA, NIST, DIN or User-defined

Temperature Compensation


0~100°C, 32~212°F

Compensation Mode


Manual or Automatic

mV



Range


-1999.9~1999.9mV

Accuracy


±0.2mV

Resolution


0.1, 1mV, Selectable

Calibration Points


1 point (Only for Relative mV mode)

Calibration Range


±200mV

Ion



Range


0.001~19999ppm, mg/L, mol/L (Refer to the range of ISE)

Accuracy


±0.5% F.S (Monovalent), ±1% F.S (Divalent)

Resolution


0.001, 0.01, 0.1, 1

Calibration Points


2 to 5 points

Calibration Solutions


0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000ppm, mg/L, mol/L

Temperature Compensation


0~100°C, 32~212°F

Compensation Mode


Manual or Automatic

Conductivity



Range


0~20.00, 200.0, 2000µS/cm, 20.00, 200.0mS/cm

Accuracy


±0.5% F.S

Calibration Points


1 to 5 points

Calibration Solutions


10µS/cm, 84µS/cm,1413µS/cm,12.88mS/cm,111.8mS/cm

Temperature Compensation


0~100°C, 32~212°F, Manual or Automatic

Temperature Coefficient


0.0~10.0%/°C

Compensation Modes


Linear or Pure Water

Cell Constant


K=0.1, 1, 10 or User-defined

Normalization Temperature


20°C or 25°C

TDS



Range


0~100ppt (Max. 200ppt, depending on factor setting)

Accuracy


±1% F.S

TDS Factor


0.1~1.0 (Default 0.5)

Salinity



Range


0~10ppt (Max. 80ppt)

Accuracy


±1% F.S

Measurement Modes


Seawater or Practical Salinity

Resistivity



Range


0~100MΩ

Accuracy


±1% F.S

Resolution


0.01, 0.1, 1

Dissolved Oxygen



Range


0.00~20.00mg/L (or ppm)

Accuracy


±0.2mg/L

Resolution


0.01mg/L

Calibration Points


1 or 2 points

Temperature Compensation


0~50°C, 32~122°F, Automatic

Pressure Correction


60.0~112.5kPa, 450~850mmHg

Salinity Correction


0~50g/L

% Saturation of Oxygen



Range


0.0~200.0%

Accuracy


±2.0%

Resolution


0.1, 1%

Temperature



Range


0~105°C, 32~221°F

Accuracy


±0.5°C, ±0.9°F

Resolution


0.1°C

Calibration Points


1 point

Calibration Range


Measured value ±10°C

Others



Hold Function


Manual or Automatic

Stability Conditions


Low or High

Calibration Due


0 to 31 days

Power Off


Manual or Automatic (10, 20, 30 minutes)

Reset Function


Yes

Memory


Stores up to 500 data sets

Output


USB Communication Interface

Connector


BNC, 6-pin Mini Plug

Power Requirements


3×1.5V "AA" Batteries

Battery Life


Approximately 150 hours (Turn off the backlit)

Dimensions


170(L)×85(W)×30(H)mm

Weight


300g

Order Code

Accessories

Bante900P-CN

E201-BNC pH Electrode

CON-1 Conductivity Electrode

DO100 Dissolved Oxygen Probe (Made in US)

TP-10K Temperature Probe

pH Buffer Pouches (pH4.01/7.00/10.01)

Conductivity Standard Solutions (84µS, 1413µS, 12.88mS)

DO Electrolyte Solution

DO Membrane Cap

AA Batteries

Carrying Case

Bante900P-UK

UK.JPG

P11 Glass pH Electrode (Made in UK)

K10 Conductivity Electrode (Made in UK)

DO100 Dissolved Oxygen Probe (Made in US)

TP-10K Temperature Probe

pH Buffer Pouches (pH4.01/7.00/10.01)

Conductivity Standard Solutions (84µS, 1413µS, 12.88mS)

DO Electrolyte Solution

DO Membrane Cap

AA Batteries

Carrying Case

Items Description
P11 pH Electrode For the general liquids
P11-LiCl pH Electrode For the non-aqueous samples
P11-HA pH Electrode For the photographic processing solutions
P11-NA pH Electrode For the biofuel
P11-DW pH Electrode For the low ionic strength samples
P12 pH Electrode For the sample in the test tube
P13 pH Electrode For the micro-volume samples
P14 pH Electrode For the outdoor applications
P15 pH Electrode For the low conductivity liquids
P16 pH Electrode For the Tris buffers
P17 pH Electrode For the semisolid samples (Flat Surface)
P18 pH Electrode For the slurries
P19 pH Electrode For the semisolid samples
P21 pH Electrode For the colloids
P22 pH Electrode For high temperature measurements
501 ORP Electrode For the sample with strong redox potential
502 ORP Electrode For the sample with weak redox potential
Na-US Sodium Electrode Range: 0.1~23000ppm
CL-US Chloride Electrode Range: 1.8~35500ppm
F-US Fluoride Electrode Range: 0.02ppm to Saturation
Ca-US Calcium Electrode Range: 0.02~4000ppm
NO3-US Nitrate Electrode Range: 0.4~62000ppm
Br-US Bromide Electrode Range: 0.4 to 79900ppm
NH4-US Ammonium Electrode Range: 0.1~18000ppm
Cn-US Cyanide Electrode Range: 0.2~260ppm
Cd-US Cadmium Electrode Range: 0.01~11200ppm
Cu-US Copper Electrode Range: 0.006~6400ppm
I-US Iodide Electrode Range: 0.06~127000ppm
Pb-US Lead Electrode Range: 0.2~20700ppm
Ag-US Silver Electrode Range: 0.01~107900ppm
K-US Potassium Electrode Range: 0.04~39000ppm
S-US Sulphide Electrode Range: 0.003~32100ppm
NH3-US Ammonia Electrode Range: 0.02~17000ppm
CON-0.1 Conductivity Electrode For the pure water
CON-1 Conductivity Electrode For the general liquids
CON-10 Conductivity Electrode For the high conductivity liquids
DO100 Dissolved Oxygen Probe Polarographic sensor
Conductivity Standard Solutions 84µS/cm, 1413µS/cm, 12.88mS/cm, 111.8mS/cm
Ion Standard Solutions 480mL/Bottle
Ionic Strength Adjuster 480mL/Bottle
pH Buffer Pouches (USA) pH4.01/7.00/10.01
pH Buffer Pouches (NIST) pH4.01/6.86/9.18
DO Electrolyte Solution 30mL/Bottle
DO Membrane Cap Special-purpose spare
TP-10K Temperature Probe Special-purpose sensor

Order Code

Dimensions

Weight

Bante900P-CN

430(L)×310(W)×100(H)mm

2kg

Bante900P-UK

430(L)×310(W)×100(H)mm

2kg